View STM6717TZWY6F_9009783.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

august 2011 doc id 11469 rev 8 1/30 1 stm6717/6718/6719/6720 stm6777/6778/6779/6780 dual/triple ultra-low voltage supervisors with push-button reset (with delay option) features primary supply (v cc1 ) monitor. fixed (factory-programmed) reset thresholds: 4.63 v to 1.58 v secondary supply (v cc2 ) monitor (stm6717/18/19/20/77/78) fixed (factory-programmed) reset thresholds: 3.08 v to 0.79 v tertiary supply monito r (using externally adjustable rstin): 0.626 v internal reference rst outputs (push-pull or open drain); state guaranteed if v cc1 or v cc2 0.8 v reset delay time (t rec ) on power-up: 13.2 ms, 210 ms, 900 ms (typ) manual reset input (mr ) optional delayed manual reset input (mrc) with external capacitor (stm6777/78/79/80) low supply current - 11 a (typ), v cc1 = v cc2 = 3.6 v operating temperature: ?40 c to 85 c (industrial grade) sot23-5 (wy) sot23-6 (wb) table 1. device summary part number monitored voltages manual reset input (mr ) delayed mr pin (mrc) reset output (rst ) package v cc1 v cc2 rstin active-low (push-pull) active-low (open drain) stm6717 ?? ? ? wy stm6718 ?? ? ? wy stm6719 ??? ? ? wb stm6720 ??? ? ? wb stm6777 ?? ? ? ? wb stm6778 ?? ? ? ? wb stm6779 ???? ? wb stm6780 ????? wb www.st.com
contents stm6717/6718/6719/6720/stm6777/6778/6779/6780 2/30 doc id 11469 rev 8 contents 1 description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1.1 pin descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1.1.1 active-low, push-pull reset output (rst ) - stm6718/20/78/80 . . . . . . . . 7 1.1.2 active-low, open drain reset output (rst ) - stm6717/19/77/79 . . . . . . . 7 1.1.3 push-button reset input (mr ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1.1.4 manual reset delay input (mrc) - stm6777/78/79/80) . . . . . . . . . . . . . . 8 1.1.5 primary supply voltage monitoring input (v cc1 ) . . . . . . . . . . . . . . . . . . . 8 1.1.6 secondary supply voltage monitoring input (v cc2 ) . . . . . . . . . . . . . . . . . 8 1.1.7 adjustable reset comparator input (rstin; stm6719/20/79/80) . . . . . . 8 2 operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.1 applications information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3 typical operating char acteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 4 maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 5 dc and ac parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 6 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 7 part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 8 revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
stm6717/6718/6719/6720/stm6777/6778/6779/6780 list of tables doc id 11469 rev 8 3/30 list of tables table 1. device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 table 2. signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 table 3. pin functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 table 4. absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 table 5. operating and ac measurement conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 table 6. dc and ac characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 table 7. t mlmh minimum pulse width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 table 8. sot23-5 ? 5-lead small outline transistor package mechanical data. . . . . . . . . . . . . . . . . 23 table 9. sot23-6 ? 6-lead small outline transistor package mechanical data. . . . . . . . . . . . . . . . . 24 table 10. carrier tape dimensions for sot23-5l and sot23-6l . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 table 11. ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 table 12. marking description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 table 13. document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
list of figures stm6717/6718/6719/6720/stm6777/6778/6779/6780 4/30 doc id 11469 rev 8 list of figures figure 1. logic diagram (stm6717/18) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 figure 2. logic diagram (stm6777/78) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 figure 3. logic diagram (stm6719/20) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 figure 4. logic diagram (stm6779/80) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 figure 5. stm6717/18 sot23-5 connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 figure 6. stm6777/78 sot23-6 connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 figure 7. stm6719/20 sot23-6 connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 figure 8. stm6779/80 sot23-6 connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 figure 9. block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 figure 10. hardware hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 figure 11. stm67xx interface to processor with bi-directional reset pins . . . . . . . . . . . . . . . . . . . . . . 10 figure 12. ensuring rst valid to v cc = 0 (active-low, push-pull outputs). . . . . . . . . . . . . . . . . . . . . . 10 figure 13. supply current vs. temperature (v cc1 = 5.5 v; v cc2 = 3.6 v) . . . . . . . . . . . . . . . . . . . . . . 11 figure 14. supply current vs. temperature (v cc1 = 3.6 v; v cc2 = 2.75 v) . . . . . . . . . . . . . . . . . . . . . 11 figure 15. supply current vs. temperature (v cc1 = 3.0 v; v cc2 = 2.0 v) . . . . . . . . . . . . . . . . . . . . . . 12 figure 16. supply current vs. temperature (v cc1 = 2.0 v; v cc2 = 1.0 v) . . . . . . . . . . . . . . . . . . . . . . 12 figure 17. normalized v cc reset time-out period vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 figure 18. maximum v cc transient duration vs. reset threshold overdrive . . . . . . . . . . . . . . . . . . . . . 13 figure 19. normalized v rst1 threshold vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 figure 20. normalized v rst2 threshold vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 figure 21. reset input threshold vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 figure 22. v cc1 -to-reset delay vs. temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 figure 23. reset input-to-reset output delay vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 figure 24. mr -to-reset output delay vs. temperature (v cc1 = 3.6v) . . . . . . . . . . . . . . . . . . . . . . . . . . 16 figure 25. ac testing input/output waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 figure 26. mr timing waveform (stm6717/18/19/20) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 figure 27. mr timing waveform (stm6777/78/79/80) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 figure 28. sot23-5 ? 5-lead small outline transistor package mechanical drawing . . . . . . . . . . . . . . 23 figure 29. sot23-6 ? 6-lead small outline transistor package mechanical drawing . . . . . . . . . . . . . . 24 figure 30. carrier tape for sot23-5l and sot23-6l . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
stm6717/6718/6719/6720/stm6777/6778/6779/6780 description doc id 11469 rev 8 5/30 1 description the stm6717/18/19/20 and stm6777/78/79/80 supervisors are a family of low-voltage/low- supply current processor (micro or dsp) supervisors, designed to monitor two (or three) system power supply voltages. they are targeted at applications such as set-top boxes (stbs), portable, battery-powered systems, networking, and communication systems. all device options have a push-button-type manual reset input (mr ). the stm6777/78/79/80 also includes an option which enables the user to delay the start of the manual reset process from 6 s (mrc pin left open) or more with external capacitor. the delay is implemented by connecting the appr opriately sized capacitor between the mrc pin and v ss (typical 4 s delay with a 3.3 f capacitor, see table 7 on page 21 ). two of the three supplies monitored (v cc1 and v cc2 ) have fixed (customer-selectable, factory-trimmed) thresholds (v rst1 and v rst2 ). the third voltage is monitored using an externally adjustable rstin thresh old (0.626 v internal reference). if any of the three monitored voltages drop below its factory-trimmed or adjustable thresholds, or if mr is asserted to logic low, a rst is asserted (driven low). once asserted, rst is maintained at low for a minimum delay period (t rec ) after all supplies rise above their respective thresholds and mr returns to high. these devices are guaranteed to be in the correct reset output logic state when v cc1 and/or v cc2 is greater than 0.8 v. these devices are available in standard 5-pin or 6-pin sot23 packages (see ta b l e 1 o n page 1 ).
description stm6717/6718/6719/6720/stm6777/6778/6779/6780 6/30 doc id 11469 rev 8 table 2. signal names figure 1. logic diagram (stm6717/18) figure 2. logic diagram (stm6777/78) figure 3. logic diagram (stm6719/20) figure 4. logic diagram (stm6779/80) ai10413 v cc1 stm6717 stm6718 v ss v cc2 rst mr ai10415 v cc1 stm6777 stm6778 v ss v cc2 rst mrc mr ai10414 v cc1 stm6719 stm6720 v ss v cc2 rst rstin mr ai10416 v cc stm6779 stm6780 v ss rst mrc rstin mr mr push-button reset input mrc manual reset delay input rst active-low reset output v cc1 primary supply voltage input v cc2 secondary supply voltage input rstin adjustable reset comparator input v ss ground
stm6717/6718/6719/6720/stm6777/6778/6779/6780 description doc id 11469 rev 8 7/30 1.1 pin descriptions 1.1.1 active-low, push- pull reset output (rst ) - stm6718/20/78/80 the rst pin is driven low and stays low whenever v cc1 or v cc2 or rstin falls below its factory-trimmed or adjustable reset threshold or when mr goes to logic low. it remains low for t rec after all supply voltages being monitored rise above their reset thresholds and mr goes from low to high. (push-pull outputs are referenced to v cc1 .) 1.1.2 active-low, open drain reset output (rst ) - stm6717/19/77/79 the rst pin is driven low and stays low whenever v cc1 or v cc2 or rstin falls below its factory-trimmed or adjustable reset threshold or when mr goes to logic low. it remains low for t rec after all supply voltages being monitored rise above their reset thresholds and mr goes from low to high. connect an external pull-up resistor to v cc1 . a 10 k pull-up resistor should be sufficient for most applications. 1.1.3 push-butto n reset input (mr ) when mr goes low the rst output is driven low. rst remains low as long as mr is low and for t rec after mr returns to high. this active-low input has an internal 50 k pull-up resistor to figure 5. stm6717/18 sot23-5 connections figure 6. stm6777/78 sot23-6 connections figure 7. stm6719/20 sot23-6 connections figure 8. stm6779/80 sot23-6 connections 1 rst v cc1 v cc2 mr v ss ai10417 2 3 4 5 1 rst v cc1 v cc2 mr v ss ai10418 2 3 4 5 6 mrc 1 rst v cc1 v cc2 mr v ss ai10419 2 3 4 6 5 rstin 1 rst v cc1 mrc mr v ss ai10420 2 3 4 6 5 rstin
description stm6717/6718/6719/6720/stm6777/6778/6779/6780 8/30 doc id 11469 rev 8 v cc1 . it can be driven from a ttl or cmos logic line, or with open drain/collector outputs, or connected to v ss through a switch. if unused, leave this pin open or connect it to v cc1 . connect a normally open momentary switch from mr to v ss ; external debounce circuitry is not required. (if mr is driven from long cables or if the device is used in noisy environments, connecting a 0.1f capacitor from mr to v ss provides additional noise immunity. 1.1.4 manual reset delay i nput (mrc) - st m6777/78/79/80) this pin is either left open or connected to v ss via a capacitor. by selecting the appropriate capacitor, the manual reset process, initiated by pressing the push-button manual reset input, can be delayed by any value from 6 s or more (see table 7 on page 21 ). 1.1.5 primary supply volt age monitoring input (v cc1 ) it also is the input for the primary reset threshold monitor. available fixed (customer- selectable, factory-programmed) reset thresholds include 4.63 v to 1.58 v. 1.1.6 secondary supply volt age monitoring input (v cc2 ) this function is available on the stm6717/18/19/20/77/78. fixed (customer-selectable, factory-programmed) reset thresholds include 3.08 v to 0.79 v. 1.1.7 adjustable reset comparator input (rstin; stm6719/20/79/80) this is a high impedance input. rst is driven low when the voltage at the rstin pin falls below 0.626 v (internal reference voltage at this comparator). the monitored voltage reset threshold is set with an external resistor-divider network. table 3. pin functions pin name function stm6717 stm6718 stm6719 stm6720 stm6777 stm6778 stm6779 stm6780 1111rst active-low reset output 3333mr push-button reset input ? ? 5 4 mrc manual reset delay input 5666v cc1 primary supply voltage input 444?v cc2 secondary supply voltage input ? 5 ? 5 rstin adjustable reset comparator input 2222v ss ground
stm6717/6718/6719/6720/stm6777/6778/6779/6780 description doc id 11469 rev 8 9/30 figure 9. block diagram 1. v cc2 input is available on stm6717/18/19/20/77/78. 2. rstin available only on stm6719/20/79/80. 3. mrc available only on stm6777/78/79/80. figure 10. hardware hookup 1. v cc2 is available only on stm6717/18/19/20/77/78. 2. rstin available only on stm6719/20/79/80. 3. mrc available only on stm6777/78/79/80. ai10421 v ref/2 = 0.626 rst compare compare compare logic t rec generator rstin (2) v cc2 (1) v cc1 v rst2 v rst1 mr mrc (3) v cc1 ai10422 v cc1 v cc2 v ss v cc1 mr mrc (3) 0.1f stm67xx rstin (2) rst rst (to processor reset) push-button switch c r1 from dc/dc converter r2 v cc2 (1) v cc3 0.1f v cc3 = (626.5mv) ( r1 + r2 r2 )
operation stm6717/6718/6719/6720/stm6777/6778/6779/6780 10/30 doc id 11469 rev 8 2 operation 2.1 applications information 1. interfacing to processors with bi-directional reset pins most processors with bi-direc tional reset pins can interface directly to the open drain rst outputs (stm6717/19/77/79). systems simultaneously requiring a push-pull rst output and a bi-directional reset interface can be in logic contention. to prevent this contention, connect a 4.7 k resistor between rst and the processor?s reset i/o as shown in figure 11 . 2. ensuring a valid rst output down to v cc =0 v the stm67xx supervisors are guaranteed to be in the correct rst output logic state when v cc1 and/or v cc2 is greater than 0.8 v. in applications which require valid reset levels down to v cc = 0, a pull-down resistor to active-low outputs (push-pull only, see figure 12 ) will ensure that the reset line is valid while the reset output can no longer sink or source current. this scheme does not work with the open drain outputs of the stm6717/19/77/79. the resistor value used is not critical, but it must be large enough not to load the reset output when v cc is above the reset threshold. for most applications, 100 k is adequate. figure 11. stm67xx interface to processor with bi-directional reset pins figure 12. ensuring rst valid to v cc = 0 (active-low, push-pull outputs) ai10425 v cc1 v cc2 v ss v cc1 stm67xx rst to other system components 4.7k v cc2 v ss processor reset ai10426 v cc1 v cc1 v ss stm67xx rst r1
stm6717/6718/6719/6720/stm6777/6778/6779/6780 typical operating characteristics doc id 11469 rev 8 11/30 3 typical operating characteristics note: typical values are at t a = 25 c unless otherwise noted. figure 13. supply current vs. temperature (v cc1 = 5.5 v; v cc2 = 3.6 v) figure 14. supply current vs. temperature (v cc1 = 3.6 v; v cc2 = 2.75 v) i cc1 i cc2 i total 0 2 4 6 8 10 12 14 16 18 ?40 ?20 0 20 40 60 80 temperature ( c) supply current (a) ai11843 i cc1 i cc2 i total 0 2 4 6 8 10 12 14 16 18 ?40 ?20 0 20 40 60 80 temperature ( c) supply current (a) ai11844
typical operating characteristics stm6717/6718/6719/6720/stm6777/6778/6779/6780 12/30 doc id 11469 rev 8 figure 15. supply current vs. temperature (v cc1 = 3.0 v; v cc2 = 2.0 v) figure 16. supply current vs. temperature (v cc1 = 2.0 v; v cc2 = 1.0 v) 0 ai11845 2 4 6 8 10 12 14 16 18 ?40 ?20 0 20 40 60 80 temperature ( c) supply current (a) i cc1 i cc2 i total 0 ai11846 2 4 6 8 10 12 14 16 18 ?40 ?20 0 20 40 60 80 temperature ( c) supply current (a) i cc1 i cc2 i total
stm6717/6718/6719/6720/stm6777/6778/6779/6780 typical operating characteristics doc id 11469 rev 8 13/30 figure 17. normalized v cc reset time-out period vs. temperature figure 18. maximum v cc transient duration vs. reset threshold overdrive 0.97 ai11847 0.99 1.01 1.03 1.05 1.07 ?40 ?20 0 20 40 60 80 temperature ( c) reset period 1 ai11848 10 100 1000 1 10 100 1000 reset threshold overdrive (mv) maximum v cc transient duration (s)
typical operating characteristics stm6717/6718/6719/6720/stm6777/6778/6779/6780 14/30 doc id 11469 rev 8 figure 19. normalized v rst1 threshold vs. temperature figure 20. normalized v rst2 threshold vs. temperature 0.996 ai11849 0.998 1.000 1.002 1.004 ?40 ?20 0 20 40 60 80 temperature ( c) v rst1 reset threshold 0.996 ai11850 0.998 1.000 1.002 1.004 ?40 ?20 0 20 40 60 80 temperature ( c) v rst2 reset threshold
stm6717/6718/6719/6720/stm6777/6778/6779/6780 typical operating characteristics doc id 11469 rev 8 15/30 figure 21. reset input threshold vs. temperature figure 22. v cc1 -to-reset delay vs. temperature 624 ai11851 625 626 627 628 629 630 ?40 ?20 0 20 40 60 80 temperature ( c) reset input threshold (mv) 28 32 36 40 44 48 ?40 ?20 0 20 40 60 80 temperature ( c) v cc1 -to-reset delay (s) ai11852
typical operating characteristics stm6717/6718/6719/6720/stm6777/6778/6779/6780 16/30 doc id 11469 rev 8 figure 23. reset input-to-reset output delay vs. temperature figure 24. mr -to-reset output delay vs. temperature (v cc1 = 3.6v) 25.0 ai11853 25.5 26.0 26.5 27.0 27.5 28.0 28.5 29.0 ?40 ?20 0 20 40 60 80 temperature ( c) rstin-to-reset output delay (s) 400 ai11854 420 440 460 480 500 ?40 ?20 0 20 40 60 80 temperature ( c) mr-to-reset output delay (ns)
stm6717/6718/6719/6720/stm6777/6778/6779/6780 maximum rating doc id 11469 rev 8 17/30 4 maximum rating stressing the device above the rating listed in the absolute maximum ratings? table may cause permanent damage to the device. these are stress ratings only and operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. refer also to the stmicroelectronics sure program and other relevant quality documents. table 4. absolute maximum ratings symbol parameter value unit t stg storage temperature (v cc off) ?55 to 150 c t sld (1) 1. reflow at peak temperature of 260 c. the time above 255 c must not exceed 30 seconds. lead solder temperature for 10 seconds 260 c v io input or output voltage ?0.3 to v cc1 + 0.3 v ?0.3 to v cc2 + 0.3 v v cc1, v cc2 supply voltage ?0.3 to 7.0 v i io input or output current (all pins) 20 ma p d power dissipation sot23-5 654 mw sot23-6 675 mw
dc and ac parameters stm6717/6718/6719/6720/stm6777/6778/6779/6780 18/30 doc id 11469 rev 8 5 dc and ac parameters this section summarizes the operating measurement conditions, and the dc and ac characteristics of the device. the parameters in the dc and ac characteristics tables that follow, are derived from tests performed under the measurement conditions summarized in table 5: operating and ac measurement conditions . designers should check that the operating conditions in their circuit match the operating conditions when relying on the quoted parameters. figure 25. ac testing input/output waveforms figure 26. mr timing waveform (stm6717/18/19/20) figure 27. mr timing waveform (stm6777/78/79/80) 1. by connecting a certain capacit or between the mrc pin and v ss , the rst can be delayed from 6 s or more (t mlmh , see table 7 on page 21 ). table 5. operating and ac measurement conditions parameter stm67xx unit v cc supply voltage 0.8 to 5.5 v ambient operating temperature (t a ) ?40 to 85 c input rise and fall times 5ns input pulse voltages 0.2 to 0.8v cc v input and output timing ref. voltages 0.3 to 0.7v cc v ai0256 8 0. 8 v cc 0.2v cc 0.7v cc 0. 3 v cc ai10423a rst mr t mlrl t rec t mlmh ai10424c rst mr t rec t mlmh (1) t mlrl
stm6717/6718/6719/6720/stm6777/6778/6779/6780 dc and ac parameters doc id 11469 rev 8 19/30 table 6. dc and ac characteristics sym alter- native description test condition (1) min typ max unit v cc operating voltage 0.8 5.5 v i cc1 v cc1 supply current v cc1 < 5.5 v, all i/o pins open 12 35 a v cc1 < 3.6 v, all i/o pins open 8 23 a i cc2 v cc2 supply current v cc2 < 3.6 v, all i/o pins open 3 9 a v cc2 < 2.75 v, all i/o pins open 2.5 7 a i li (2) input leakage current 0 v = v in = v cc ?1 +1 a i lo open drain rst output leakage current v cc1 > v rst1 , v cc2 > v rst2 ; rst not asserted 0.5 a v ol output low voltage (rst ; push-pull or open drain) v cc1 or v cc2 0.8 v, i sink = 1 a, rst asserted 0.3 v v cc1 or v cc2 1.0 v, i sink = 50 a, rst asserted 0.3 v v cc1 or v cc2 1.2 v, i sink = 100 a, rst asserted 0.3 v v cc1 or v cc2 2.7 v, i sink = 1.2 ma, rst asserted 0.3 v v cc1 or v cc2 4.5 v, i sink = 3.2 ma, rst asserted 0.4 v v oh output high voltage (rst ; push-pull only) v cc1 1.8 v, i source = 200 a, rst not asserted 0.8v cc1 v v cc1 2.7 v, i source = 500 a, rst not asserted 0.8v cc1 v v cc1 4.5 v, i source = 800 a, rst not asserted 0.8v cc1 v t r (3) push-pull rst rise time (stm6718/20/78/80) rise time measured from 10% to 90% of v cc ; c l = 5 pf, v cc = 3.3 v 525ns reset thresholds v rst (4) v th1 v cc1 reset threshold l (falling) 4.500 4.625 4.750 v m (falling) 4.250 4.375 4.500 v t (falling) 3.000 3.075 3.150 v s (falling) 2.850 2.925 3.000 v r (falling) 2.550 2.625 2.700 v z (falling) 2.250 2.313 2.375 v y (falling) 2.125 2.188 2.250 v w (falling) 1.620 1.665 1.710 v v (falling) 1.530 1.575 1.620 v
dc and ac parameters stm6717/6718/6719/6720/stm6777/6778/6779/6780 20/30 doc id 11469 rev 8 v rst2 (4) v th2 v cc2 reset threshold t (falling) 3.000 3.075 3.150 v s (falling) 2.850 2.925 3.000 v r (falling) 2.550 2.625 2.700 v z (falling) 2.250 2.313 2.375 v y (falling) 2.125 2.188 2.250 v w (falling) 1.620 1.665 1.710 v v (falling) 1.530 1.575 1.620 v i (falling) 1.350 1.388 1.425 v h (falling) 1.275 1.313 1.350 v g (falling) 1.080 1.110 1.140 v f (falling) 1.020 1.050 1.080 v k (falling) 0.895 0.925 0.955 v j (falling) 0.845 0.875 0.905 v e (falling) 0.810 0.833 0.855 v d (falling) 0.765 0.788 0.810 v v hyst reset threshold hysteresis referenced to v rst typical 0.5 % t rd v cc to rst delay v cc1 = (v rst1 + 100 mv) to (v rst ? 100 mv) 20 s v cc2 = (v rst2 + 75 mv) to (v rst2 ? 75 mv) 20 s t rec t rp rst pulse width blank 140 210 280 ms b 8.8 13.2 17.6 g 600 900 1200 adjustable reset comparat or input (stm6719/20/79/80) v rstin rstin input threshold 611 626.5 642 mv i rstin rstin input current ?25 +25 na rstin hysteresis 3 mv t rstind rstin to rst output delay v rstin to (v rstin ? 30 mv) 22 s table 6. dc and ac characteristics (continued) sym alter- native description test condition (1) min typ max unit
stm6717/6718/6719/6720/stm6777/6778/6779/6780 dc and ac parameters doc id 11469 rev 8 21/30 manual (push-button) reset input v il mr input voltage 0.3v c c1 v v ih 0.7v cc1 v t mlmh t mr mr minimum pulse width (stm6717/18/19/20) 1s mr minimum pulse width (stm6777/78/79/80) mrc connected via capacitor to v ss 6s t mlrl t mrd mr to rst output delay 200 ns mr glitch immunity (stm6717/18/19/20) 100 ns mr pull-up resistance 25 50 80 k 1. valid for ambient operating temperature: t a = ?40 to 85 c; v cc1 = 0.8 to 5.5 v and v cc2 = 0.8 to 3.6 v (except where noted). 2. input leakage for the mrc pin is not tested. 3. guaranteed by design. 4. the leakage current measured on the rst pin is tested with the reset de-asserted (output high impedance). table 6. dc and ac characteristics (continued) sym alter- native description test condition (1) min typ max unit table 7. t mlmh minimum pulse width v cc1 capacitor value (1) 100 pf 0.1 f 2.2 f 3.3 f 4.7 f 6.8 f 1.6 v 120 s 120 ms 2.6 s 4.0 s 5.6 s 8.2 s 2.0 v 122 s 122 ms 2.7 s 4.0 s 5.8 s 8.3 s 3.0 v 125 s 125 ms 2.7 s 4.1 s 5.9 s 8.5 s 4.0 v 128 s 129 ms 2.8 s 4.2 s 6.0 s 8.7 s 5.0 v 130 s 130 ms 2.8 s 4.3 s 6.1 s 8.8 s 1. at 25 c (typical)
package mechanical data stm6717/6718/6719/6720/stm6777/6778/6779/6780 22/30 doc id 11469 rev 8 6 package mechanical data in order to meet environmental requirements, st offers these devices in different grades of ecopack ? packages, depending on their level of environmental compliance. ecopack ? specifications, grade definitions and product status are available at: www.st.com . ecopack ? is an st trademark.
stm6717/6718/6719/6720/stm6777/6778/6779/6780 package mechanical data doc id 11469 rev 8 23/30 figure 28. sot23-5 ? 5-lead small outline transistor package mechanical drawing note: drawing is not to scale. note: dimensions per jedec sot/sop pr oduct outline mo-178c, variation aa c 0.10 a a2 a1 5x c d e1 e e a m cab 5x b 0.20 1 b e1 c l datum a 0.20 0133778 table 8. sot23-5 ? 5-lead small outline transistor package mechanical data symb mm inches min typ max min typ max a??1.45??0.057 a1 ? ? 0.15 ? ? 0.006 a2 0.90 1.15 1.30 0.035 0.045 0.051 b 0.30 ? 0.50 0.012 ? 0.020 c 0.08 ? 0.22 0.003 ? 0.009 d ? 2.90 ? ? 0.114 ? e ? 2.80 ? ? 0.110 ? e1 ? 1.60 ? ? 0.063 ? e ? 0.95 ? ? 0.037 ? e1 ? 1.90 ? ? 0.075 ? l 0.30 0.45 0.60 0.012 0.018 0.024 q048048 n5 5
package mechanical data stm6717/6718/6719/6720/stm6777/6778/6779/6780 24/30 doc id 11469 rev 8 figure 29. sot23-6 ? 6-lead small outline transistor package mechanical drawing note: drawing is not to scale. note: dimensions per jedec sot/sop pr oduct outline mo-178c variation ab e1 d e 6x b e a m 0.10 c a b 1 0.10 c a a2 a1 6x c b e1 c datum a 0.20 l 7049714 table 9. sot23-6 ? 6-lead small outline transistor package mechanical data symb mm inches min typ max min typ max a??1.45??0.057 a1 ? ? 0.15 ? ? 0.006 a2 0.90 1.15 1.30 0.035 0.045 0.051 b 0.30 ? 0.50 0.012 ? 0.020 c 0.08 ? 0.22 0.003 ? 0.009 d ? 2.90 ? ? 0.114 ? e ? 2.80 ? ? 0.110 ? e1 ? 1.60 ? ? 0.063 ? e ? 0.95 ? ? 0.037 ? e1 ? 1.90 ? ? 0.075 ? l 0.30 0.45 0.60 0.012 0.018 0.024 q048048 n6 6
stm6717/6718/6719/6720/stm6777/6778/6779/6780 package mechanical data doc id 11469 rev 8 25/30 figure 30. carrier tape for sot23-5l and sot23-6l note: part pin 1 indicator is on bottom left for shipping method ?f? and is on top right for shipping method ?r? see section 7 . t k 0 p 1 a 0 b 0 p 2 p 0 center line s of cavity w e f d top cover tape u s er direction of feed am0 3 07 3 v1 table 10. carrier tape dimensions for sot23-5l and sot23-6l package w d e p 0 p 2 fa 0 b 0 k 0 p 1 tunit bulk qty sot23-5 sot23-6 8.00 +0.30/ ?0.10 1.50 +0.10/ ?0.00 1.75 0.10 4.00 0.10 2.00 0.10 3.50 0.05 3.23 0.10 3.17 0.10 1.37 0.10 4.00 0.10 0.254 0.013 mm 3000
part numbering stm6717/6718/6719/6720/stm6777/6778/6779/6780 26/30 doc id 11469 rev 8 7 part numbering table 11. ordering information scheme example: stm67xx lt wy 6 f device type stm67xx reset thresholds (v rst1 and v rst2 ) for v cc1 and v cc2 stm6717/18/19/20/77/78 (v rst1 and v rst2 ) stm6779/80 (v rst1 only) suffix v rst1 v rst2 suffix v rst1 lt 4.625 3.075 l? (1) 4.625 ms 4.375 2.925 t? (1) 3.075 mr 4.375 2.625 s? (1) 2.925 tz (1) 3.075 2.313 y? (1) 2.188 tw (1) 3.075 1.665 v? (1) 1.575 ti 3.075 1.388 r? 2.625 tg (1) 3.075 1.110 z? 2.313 tk 3.075 0.925 te 3.075 0.833 sy (1) 2.925 2.188 sv (1) 2.925 1.575 sh (2) 2.925 1.313 sf (1) 2.925 1.050 sj (3) 2.925 0.875 sd (3) 2.925 0.788 yv 2.188 1.575 yh 2.188 1.313 yf 2.188 1.050 yj 2.188 0.875 yd 2.188 0.788 vh 1.575 1.313 vf 1.575 1.050 vj 1.575 0.875 vd 1.575 0.788 reset pulse width blank: t rec = 140 ms to 280 ms b: t rec = 8.8 ms to 17.6 ms g: t rec = 600 ms to 1200 ms package wy = sot23-5 wb = sot23-6 temperature range 6 = ?40 to 85c shipping method e = ecopack ? package, tubes f = ecopack ? package, tape and reel r (4) = ecopack ? package, tape and reel (pin 1 at top right). 1. t hese are standard versions and are typically held in stock. a non-standard version may require a higher minimum volumes, and/or longer delivery times. for other options, or for more information on an y aspect of this device, please contact the st sales office nea rest you. 2. available in stm6719 version only. 3. available in stm6717 version only. 4. available for stm6720sy, stm671 9sf and stm6719sfb versions only.
stm6717/6718/6719/6720/stm6777/6778/6779/6780 part numbering doc id 11469 rev 8 27/30 table 12. marking description part number v rst1 threshold (v) v rst2 threshold (v) topside marking bottomside marking stm6717sd 2.925 0.788 7sd1 pyww stm6717sj 2.925 0.875 7sj1 pyww stm6717sf 2.925 1.050 7sf1 pyww stm6717tg 3.075 1.110 7tg1 pyww stm6717tgg 3.075 1.110 7tg9 pyww stm6717tw 3.075 1.665 7tw1 pyww stm6717sv 2.925 1.575 7sv1 pyww stm6717sy 2.925 2.188 7sy1 pyww stm6717tz 3.075 2.313 7tz1 pyww stm6718sf 2.925 1.050 7sf2 pyww stm6718tg 3.075 1.110 7tg2 pyww stm6718tw 3.075 1.665 7tw2 pyww stm6718sv 2.925 1.575 7sv2 pyww stm6718sy 2.925 2.188 7sy2 pyww stm6718tz 3.075 2.313 7tz2 pyww stm6719sf 2.925 1.050 7sf3 pyww stm6719sfb 2.925 1.050 7sfb pyww stm6719tg 3.075 1.110 7tg3 pyww stm6719sh 2.925 1.313 7sh3 pyww stm6719tw 3.075 1.665 7tw3 pyww stm6719sv 2.925 1.575 7sv3 pyww stm6719sy 2.925 2.188 7sy3 pyww stm6719tz 3.075 2.313 7tz3 pyww stm6720sf 2.925 1.050 7sf4 pyww stm6720tg 3.075 1.110 7tg4 pyww stm6720tw 3.075 1.665 7tw4 pyww stm6720sv 2.925 1.575 7sv4 pyww stm6720sy 2.925 2.188 7sy4 pyww stm6720tz 3.075 2.313 7tz4 pyww stm6777sf 2.925 1.050 7sf5 pyww stm6777tg 3.075 1.110 7tg5 pyww stm6777tw 3.075 1.665 7tw5 pyww stm6777sv 2.925 1.575 7sv5 pyww stm6777sy 2.925 2.188 7sy5 pyww stm6777tz 3.075 2.313 7tz5 pyww
part numbering stm6717/6718/6719/6720/stm6777/6778/6779/6780 28/30 doc id 11469 rev 8 note: for topside marking, ?7? is th e family number, followed by the v rst1 threshold, v rst2 threshold and device number (1,9 = stm6717, 2 = 6718, 3 = 6719, 4 = 6720, 5 = 6777, 6 = 6778, 7 = 6779, 8 = 6780). for bottomside marking, ?p? = assembly site, ?y? = 1-digit year, and ?ww? = 2-digit work week. stm6778sf 2.925 1.050 7sf6 pyww stm6778tg 3.075 1.110 7tg6 pyww stm6778tw 3.075 1.665 7tw6 pyww stm6778sv 2.925 1.575 7sv6 pyww stm6778sy 2.925 2.188 7sy6 pyww stm6778tz 3.075 2.313 7tz6 pyww stm6779l 4.625 ? 7lx7 pyww stm6779t 3.075 ? 7tx7 pyww stm6779s 2.925 ? 7sx7 pyww stm6779y 2.188 ? 7yx7 pyww stm6779v 1.575 ? 7vx7 pyww stm6780l 4.625 ? 7lx8 pyww stm6780t 3.075 ? 7tx8 pyww stm6780s 2.925 ? 7sx8 pyww stm6780y 2.188 ? 7yx8 pyww stm6780v 1.575 ? 7vx8 pyww table 12. marking description (continued) part number v rst1 threshold (v) v rst2 threshold (v) topside marking bottomside marking
stm6717/6718/6719/6720/stm6777/6778/6779/6780 revision history doc id 11469 rev 8 29/30 8 revision history table 13. document revision history date revision changes 18-oct-2004 1 first draft 25-oct-2004 1.1 descriptive text, sales types ( ta bl e 1 1 ) 14-jan-2005 1.2 update characteristics, pin functions ( ta b l e 2 ) 09-feb-2005 1.3 update characteristics ( figure 9 ; ta bl e 3 ) 08-apr-2005 1.4 update characteristics and mechanical dimensions; add table ( figure 9 , 10 , 27 , 28 , 29 ; ta b l e 4 , 6 , 11 , 8 , 9 ) 28-jul-2005 1.5 update characteristics, reset delay ( figure 10 , 27 ; ta b l e 4 , 6 , 7 , 11 ) 13-sep-2005 2 add operating characteristics; updat e timings, document status, lead- free text (figure figure 13 , 14 , 15 , 16 , 17 , 18 , 19 , 20 , 21 , 22 , 23 , 24 , 26 , 27 ; ta bl e 1 1 ) 07-oct-2005 3 marked stm6779/6780 as availability request parts ( ta b l e 1 , 11 ) 07-feb-2007 4 updated stm6779/6780 availability (cover page, ta b l e 1 , 11 ) 12-jun-2007 5 updated ta bl e 1 1 , added table 12: marking description . 05-dec-2007 6 updated cover page, ta bl e 6 , 11 , and 12 . 22-mar-2010 7 updated features ; ta bl e 6 , 8 , 9 , 11 , 12 ; footnote 1 of ta b l e 4 ; section 6: package mechanical data ; added tape and reel specifications ( figure 30 , ta bl e 1 0 , footnote 4 of ta bl e 1 1 ); reformatted document. 02-aug-2011 8 removed footnote from table 6: dc and ac characteristics .
stm6717/6718/6719/6720/stm6777/6778/6779/6780 30/30 doc id 11469 rev 8 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a parti cular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. unless expressly approved in writing by two authorized st representatives, st products are not recommended, authorized or warranted for use in milita ry, air craft, space, life saving, or life sustaining applications, nor in products or systems where failure or malfunction may result in personal injury, death, or severe property or environmental damage. st products which are not specified as "automotive grade" may only be used in automotive applications at user?s own risk. resale of st products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or registered trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2011 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - philippines - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com

▲Up To Search▲

Price & Availability of STM6717TZWY6F

	To Download STM6717TZWY6F Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .